WIREREADY Product Information Sheet: KB-CCH/1 - CLOSURE COLLECTOR HARNESS ³ ³ ³ ³ ÀÄ¿ ÚÄÙ ÀÄ¿ ÚÄÙ ³T³ R R ³T³ ³O³ P E P E ³O³ ³ ³ A P S C A P S C ³ ³ ³P³ U + L T + O U + L T + O ³P³ ³C³³ S 1 A O 1 R ³ ³ S 1 A O 1 R ³³C³ ³ À´ E 0 Y P 0 D ³ ³ E 0 Y P 0 D ÃÙ ³ ÀÄÄ´ Ú¿ Ú¿ Ú¿ Ú¿ Ú¿ Ú¿ ³ ³ Ú¿ Ú¿ Ú¿ Ú¿ Ú¿ Ú¿ ÃÄÄÙ ÀÄÙÀÄÙÀÄÙÀÄÙÀÄÙÀÄÙÀÄÙ ÀÄÙÀÄÙÀÄÙÀÄÙÀÄÙÀÄÙÀÄÙ CTS TD RI DSR RTS CD CTS TD RI DSR RTS CD Product Includes: - One(1) KB-CCH/1 Closure Collector Harness (Dual Sided) - Two(2) (25 male to 25 female) straight-through serial cables - Two(2) RS-232 Mini-testers - Two(2) (25 male to 9 female) adaptors These instructions cover: 1) THE PURPOSE OF THE KB-CCH/1. 2) HOW TO SET UP THE HARDWARE. 3) HOW TO SET UP THE SOFTWARE. 4) HOW THE KB-CCH/1 WORKS. 5) HOW TO MAKE YOUR OWN CLOSURE COLLECTOR HARNESS. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ THE PURPOSE OF THE KB-CCH/1 The KB-CCH/1 is for use with CartReady. The KB-CCH/1 allows you to PAUSE, PLAY, STOP, and RECORD carts from the Notepad*, Cart Deck #1, and/or Cart Deck #2. At the very least, the KB-CCH/1 allows you to control the carts just as if you were using the keyboard. However, their is one major advantage to using the KB-CCH/1 over the keyboard. That is, the KB-CHH/1 can execute commands (Pause, Play, Stop, & Record) anywhere in the program. FOR EXAMPLE: You can load a blank cart into Cart Deck #1, then go to the Notepad and press the RECORD button on the KB-CCH/1 that controls Cart Deck #1, and you will be recording onto the cart in Cart Deck #1 - even though you are on the Notepad screen. OR You could be on the other side of the studio and when it is time to execute a command, just push a button. As long as you set the cart(s) up in advance, You don't have to got to the PC, you don't have to get to the right screen - you just have to push ONE button. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ * - The KB-CCH/1, like the keyboard, only enables PLAY & STOP for carts loaded for play in the Notepad, NOT PAUSE & RECORD. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ HOW TO SET UP THE HARDWARE Connecting the KB-CCH/1 to the PC: You will need ONE available com port (serial port) for EACH area (Notepad, Cart Deck #1, and/or Cart Deck #2) you want to control with the KB-CCH/1. FOR EXAMPLE: IF YOU ONLY WANT TO CONTROL CART DECK #1 REMOTELY, YOU ONLY NEED ONE AVAILABLE COM PORT. YOU WOULD USE ONE SIDE OF A KB-CCH/1. IF YOU WANT TO CONTROL CART DECK #1 AND THE NOTEPAD, YOU NEED TWO AVAILABLE COM PORTS. YOU WOULD USE BOTH SIDES OF A KB-CCH/1. IF YOU WANT TO CONTROL ALL 3 AREAS (NOTEPAD, CART DECK #1, AND CART DECK #2), YOU NEED 3 AVAILABLE COM PORTS. YOU WOULD USE BOTH SIDES OF ONE KB-CCH/1 AND ONLY ONE SIDE OF A SECOND KB-CCH/1. 1) WE SUGGEST THAT YOU TURN THE COMPUTER OFF WHEN YOU CONNECT OR DISCONNECT ANY DEVICES. CONNECT THE KB-CCH/1(S) TO THE COM PORT(S) ON THE PC USING THE SERIAL CABLES WHICH HAVE BEEN INCLUDED. Connecting KB-CCH/1 to Push Buttons: You need to furnish the push buttons that will be used to operate the KB-CCH/1(s). The push-buttons just have to make a closure between 2 wires. See diagram below... PUSH BUTTON ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Wire #1 ³³ Wire #1 ³ ³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ ³ ÚÄÙ ³³ ÚÄ´ ³ ³ ÀÄ¿ ³³ ÀÄ´ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ ³ Wire #2 ³³ Wire #2 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ NO closure in normal position CLOSURE in pushed position HOW TO SET UP THE HARDWARE cont. You will need 4 push buttons for each Cart Deck you will be controlling, and only 2 push buttons for the notepad. 1) CONNECT YOUR PUSH BUTTONS TO THE SCREW DOWNS ON THE BARRIER STRIP OF THE KB-CCH/1. As shown below... ³ ³ ÀÄ¿ ÚÄÙ ³T³ R ³O³ P E ³ ³ A P S C ³P³ U + L T + O ³C³³ S 1 A O 1 R ³ ³ À´ E 0 Y P 0 D ³ ÀÄÄ´ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ³ ÀÄÙ ³ÀÄÙ³³ÀÄÙ³ ÀÄÙ ³ÀÄÙ³³ÀÄÙ³ ÀÄÙ ³ ³³ ³ ³ ³³ ³ ³ ³³ ³ ³ ³³ ³ ³ ³³ ³ ³ ³³ ³ ³ ³³ ³ ³ ³³ ³ À¿ ÚÙÀ¿ ÚÙ À¿ ÚÙÀ¿ ÚÙ PUSH BUTTONS ->ÀÄÙ ÀÄÙ ÀÄÙ ÀÄÙ If you have questions about making the push buttons, see "HOW THE KB-CCH/1 WORKS". ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ HOW TO SET UP THE SOFTWARE CartReady needs to be configured in order for the KB-CCH/1 to be used. 1) FROM THE MAIN CART DECK SCREEN, PRESS F10. 2) PRESS C, OR HIGHLIGHT CONFIGURATION CHANGES AND PRESS ENTER. 3) HIGHLIGHT GLOBAL CHANNELS (IF NOT ALREADY HIGHLIGHTED), AND PRESS ENTER. THIS OPTION BOX WILL OPEN: ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿³ ³ Global Channels ³³ ³ ³³ ³ Notepad Channel : Not Assigned ³³ ³ Cart Deck 1 Channel : Not Assigned ³³ ³ Cart Deck 2 Channel : Not Assigned ÃÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 4) HIGHLIGHT THE AREA (NOTEPAD, CART DECK 1, OR CART DECK 2) WHICH YOU WANT TO USE A KB-CCH/1 WITH, AND PRESS ENTER TO SELECT THE CHANNEL. THIS OPTION BOX WILL OPEN: ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿³ ³ Not Assigned ³³ ³ Channel 1 3F8 ³³ ³ Channel 2 2F8 ³³ ³ Channel 3 3E8 ³³ ³ Channel 4 2E8 ³³ ³ Channel 5 2A0 ³³ ³ Channel 6 2A8 ³³ ³ Channel 7 2B0 ³³ ³ Channel 8 2B8 ³³ ³ Channel 9 1A0 ³³ ³ Channel 10 1A8 ³³ ³ Channel 11 1B0 ³³ ³ Channel 12 1B8 ÃÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 5) HIGHLIGHT THE CHANNEL (COM PORT ADDRESS) WHICH THE KB-CCH/1 THAT WILL BE CONTROLLING THE SELECTED AREA IS CONNECTED, AND PRESS ENTER. HOW TO SET UP THE SOFTWARE cont. 6) REPEAT STEPS 4 & 5 FOR EACH AREA YOU WILL BE CONTROLLING WITH A KB-CCH/1. REMEMBER: EACH CHANNEL (COM PORT) CAN ONLY CONTROL ONE AREA (NOTEPAD, CART DECK #1, OR CART DECK #2). 7) IF THERE IS AN AREA WHICH YOU WILL NOT BE CONTROLLING WITH A KB-CCH/1, A CHANNEL SHOULD NOT BE ASSIGNED. IF A CHANNEL IS SELECTED, HIGHLIGHT THE AREA, PRESS ENTER, HIGHLIGHT NOT ASSIGNED, AND PRESS ENTER. 8) WHEN YOU ARE THROUGH ASSIGNING THE CHANNELS, PRESS ESCAPE. 9) THE CHANGES YOU HAVE JUST MADE HAVE BEEN RECORDED IN CARTREADY'S CONFIGURATION FILE ($CONFIG.WR). IN ORDER FOR THE CHANGES TO TAKE EFFECT, YOU MUST EXIT TO DOS, AND THEN COME BACK INTO CARTREADY. 10) CONFIRM THAT THE KB-CCH1(S) IS/ARE WORKING AS THEY SHOULD WITH THE AREAS YOU SET THEM UP TO WORK WITH. ONCE YOU CONFIRM THAT THE HARDWARE AND SOFTWARE ARE BOTH SET UP PROPERLY, YOU SHOULD WRITE DOWN THE COM PORT THAT EACH KB-CCH/1 IS CONNECTED TO AND WHICH AREA IT IS CONTROLLING. THERE ARE SPACES ON THE KB-CCH/1 BOARD TO WRITE THIS INFORMATION. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ HOW THE KB-CCH/1 WORKS The com ports on your PC have lines (also called pins) for communicating with external devices. The KB-CCH/1 uses 6 of these lines. Two of the lines are outputs (TD & RTS) which CartReady drives with +10 volts. The other 4 lines are inputs (CTS, RI, DSR, & CD) which, for all intensive purposes have 0 volts. The only way that the voltage of an input line can be changed from 0 volts to +10 volts, is to have something energize the line with +10 volts. That is exactly what happens when the push button is pressed. The push button brings the input line (0 volts) in contact with the output line (+10 volts) which raises the voltage on the input line to +10 volts. CartReady is constantly driving the 2 output lines, and monitoring the 4 input lines. All that CartReady is doing is watching these 4 input lines to see if any of them go to +10 volts. And as we now know, the only way that an input line gets to be +10 volts, is by bringing the input line in contact with the output line. And the way that these two lines (the input and the output) come in contact is by the push button getting pressed. When CartReady sees that one of the input lines is +10 volts, rather than 0 volts, it executes the command (Pause, Play, Stop, or Record) which is associated with the Input line that went to +10 volts (refer to diagrams on pages 1 & 3). ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ HOW TO MAKE YOUR OWN CONTACT COLLECTOR HARNESS: READ "HOW THE KB-CCH/1 WORKS" BEFORE READING THIS SECTION. 1) LOCATE (OR MAKE) A STRAIGHT THROUGH SERIAL CABLE WHICH HAS THE PROPER SIZE CONNECTOR FOR THE COM PORT (9 pin or 25 pin) ON THE PC. 2) IF YOU ARE USING A PRE-MADE CUT OFF THE END OF THE CABLE THAT WILL NOT BE CONNECTED TO THE PC. 3) YOU THEN CONNECT THE PUSH BUTTONS TO THE PINS AS OUTLINED BELOW*. IF YOU HAVE QUESTIONS, SEE : "HOW TO SET UP THE HARDWARE". IF THE COM PORT ON THE PC IS A 9 PIN: The push-button for PAUSE will use pins: 3(TD) & 8 (CTS). The push-button for PLAY will use pins: 3(TD) & 9 (RI). The push-button for STOP will use pins: 7(RTS) & 6 (DSR). The push-button for RECORD will use pins: 7(RTS) & 1 (CD). IF THE COM PORT ON THE PC IS A 25 PIN: The push-button for PAUSE will use pins: 2(TD) & 5 (CTS). The push-button for PLAY will use pins: 2(TD) & 22 (RI). The push-button for STOP will use pins: 4(RTS) & 6 (DSR). The push-button for RECORD will use pins: 4(RTS) & 8 (CD). 4) ONCE THE PUSH BUTTONS ARE CONNECTED FOLLOW THE INSTRUCTIONS: "HOW TO SET UP THE HARDWARE".AND "HOW TO SET UP THE SOFTWARE" in the previous pages. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ * - IT IS A GOOD IDEA TO DO A CONTINUITY CHECK IF YOU ARE UNSURE OF WHICH OF THE LOOSE WIRES CORRESPOND TO WHICH PINS ON THE CONNECTOR. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ